Program Your Remote or Keypad

• 1
  Press & release the yellow Learn button on your opener
  The light should turn on. You have 30 seconds.
• 2
  Press & hold the button on the 893LM remote (2-3 seconds)
  The opener light will blink—your remote is programmed.
• 3
  Test it
  Stand 15 feet away and press the button. Door should open/close.

  ✓ If it works, you’re done!

Need Help?

• 1
  Press & release the yellow Learn button on your first opener
  The light should turn on. You have 30 seconds.
• 2
  Press & hold the first button on the 885LM (2-3 seconds)
  Button 1 = Door 1. The opener light will blink when programmed.
• 3
  Repeat for the second door with Button 2
  Press Learn button on Door 2 opener, then hold Button 2 on remote.
• 4
  Test both buttons
  Stand 15 feet away from each door and test.

  ✓ Each button should operate its assigned door

Need Help?

• 1
  For each door, press the yellow Learn button on that opener
  Light comes on. You have 30 seconds.
• 2
  Press & hold one button on the 893MAX (2-3 seconds)
  Button 1 = Door 1, Button 2 = Door 2, Button 3 = Door 3.

  Opener light blinks = success

• 3
  Repeat steps 1-2 for each additional door
  Program Button 2 to Door 2 opener, then Button 3 to Door 3 opener.
• 4
  Test all buttons
  Each button should operate its assigned door.

Need Help?

• 1
  Press & release the yellow Learn button on your first opener
  Light comes on. You have 30 seconds.
• 2
  Press & hold the first button on the 877LM (2-3 seconds)
  Button 1 = Door 1. Opener light will blink to confirm.
• 3
  Repeat steps 1-2 for each additional door (up to 4)
  Program buttons 2, 3, and 4 to their respective doors or functions.
• 4
  Test all buttons
  Each button should operate its assigned door or function.

  Hold button for 2-3 seconds if door doesn’t respond

Need Help?

• 1
  Install 4 AA batteries in the keypad
  Make sure polarity is correct (+/- matches).
• 2
  Mount keypad on your garage wall (within 40 feet of opener)
  Install at comfortable height for entering PIN code.
• 3
  Press & release the yellow Learn button on opener
  Light comes on. You have 30 seconds.
• 4
  Enter your 4-digit PIN code on the keypad
  Example: 1234. Then press # or Enter. Opener light blinks = success.

  Choose a PIN you’ll remember easily

• 5
  Test the keypad
  Enter your PIN + # at the keypad. Door should open/close.

Need Help?

• 1
  Install 2 AA batteries in the keypad
  Check battery contacts for corrosion. Replace if necessary.
• 2
  Mount keypad on your garage wall (within 40 feet of opener)
  Place at a comfortable height, away from direct water exposure.
• 3
  Press & release the yellow Learn button on opener
  Light comes on. You have 30 seconds to proceed.
• 4
  Enter your 3-6 digit PIN code on the keypad
  Then press the # button. Opener light blinks = success.

  Use numbers 0-9 and avoid simple sequences like 1234

• 5
  Test the keypad from outside
  Enter your PIN + # and verify door opens/closes.

Need Help?

• 1
  Position sensors on both sides of the garage door opening
  Mount 4-6 inches above the floor for optimal detection range.
• 2
  Ensure sensors face each other directly
  Sensors should have a clear line of sight to each other. Use a level to align.
• 3
  Connect wires to the sensor terminals on your opener
  Follow the color coding: White = trigger, Black = ground.

  Use 18 AWG or thicker wire for runs over 50 feet

• 4
  Check sensor alignment lights
  Both sensors should show a steady red light. If not, realign them.
• 5
  Test safety reversal
  Close the door and wave your hand in the beam. Door should reverse.

Need Help?

• 1
  Press & release the yellow Learn button on your opener The light should turn on. You have 30 seconds.
• 2
  Press & hold the button on the L91S remote (2-3 seconds) The opener light will blink—your remote is programmed.
• 3
  Test it Stand 15 feet away and press the button. Door should open/close.

  ✓ If it works, you’re done!

Need Help?

• 1
  Press & release the yellow Learn button on your opener The light should turn on. You have 30 seconds.
• 2
  Press & hold the first button on the L932M (2-3 seconds) Button 1 = Door 1. The opener light will blink when programmed.
• 3
  Repeat for the second door with Button 2 Press Learn button on Door 2 opener, then hold Button 2 on remote.
• 4
  Test both buttons Stand 15 feet away from each door and test.

  ✓ Each button should operate its assigned door

Need Help?

• 1
  Press & release the yellow Learn button on your opener The light should turn on. You have 30 seconds.
• 2
  Press & hold the button on the L991S remote (2-3 seconds) The opener light will blink to confirm programming.
• 3
  Test from your vehicle Drive up and test the remote. Door should operate smoothly.

  ✓ Mount clip on sun visor for easy access

Need Help?

• 1
  For each door, press the yellow Learn button on that opener Light comes on. You have 30 seconds.
• 2
  Press & hold one button on the L993S (2-3 seconds) Button 1 = Door 1, Button 2 = Door 2, Button 3 = Door 3.

  Opener light blinks = success
• 3
  Repeat steps 1-2 for each additional door Program Button 2 to Door 2 opener, then Button 3 to Door 3 opener.
• 4
  Test all buttons from your vehicle Each button should operate its assigned door independently.

Need Help?

• 1
  For each door, press the yellow Learn button on that opener Light comes on. You have 30 seconds.
• 2
  Press & hold one button on the L993M (2-3 seconds) Button 1 = Door 1, Button 2 = Door 2, Button 3 = Door 3.

  MAX tier compatible with many LiftMaster models
• 3
  Repeat steps 1-2 for each additional door Program Button 2 to Door 2 opener, then Button 3 to Door 3 opener.
• 4
  Test all three buttons Each button should operate its assigned door.

Need Help?

• 1
  Install 4 AA batteries in the keypad Make sure polarity is correct (+/- matches).
• 2
  Mount keypad on your garage wall (within 40 feet of opener) Install at comfortable height for entering PIN code.
• 3
  Press & release the yellow Learn button on opener Light comes on. You have 30 seconds.
• 4
  Enter your 4-digit PIN code on the keypad Example: 1234. Then press # or Enter. Opener light blinks = success.

  Choose a PIN you’ll remember easily
• 5
  Test the keypad Enter your PIN + # at the keypad. Door should open/close.

Need Help?

• 1
  Install 4 AA batteries in the keypad Check battery contacts for proper alignment.
• 2
  Mount keypad on your garage wall (within 40 feet of opener) Place at a comfortable height, away from direct water exposure.
• 3
  Press & release the yellow Learn button on opener Light comes on. You have 30 seconds to proceed.
• 4
  Enter your 4-digit PIN code on the keypad Then press the # button. Opener light blinks = success.

  Avoid simple sequences like 1234 or 0000
• 5
  Test the keypad from outside Enter your PIN + # and verify door opens/closes.

Need Help?

• 1
  Install 4 AA batteries in the keypad Verify polarity (+/-) matches the battery compartment markings.
• 2
  Mount keypad on your garage wall (within 40 feet of opener) Choose a location with clear line of sight to the opener.
• 3
  Press & release the yellow Learn button on opener Light comes on. You have 30 seconds.
• 4
  Enter your 4-6 digit PIN code on the keypad Then press # to confirm. Opener light blinks = success.

  Universal design works with most LiftMaster openers
• 5
  Test the keypad Enter your PIN + # at the keypad. Door should open/close.

Need Help?

• 1
  Install 4 AA batteries in the panel Make sure battery polarity is correct (+/- matches).
• 2
  Choose mounting location on your garage wall Mount at comfortable height, 40 feet or less from opener.
• 3
  Press & release the yellow Learn button on opener Light comes on. You have 30 seconds.
• 4
  Press & hold the open/close button on the L956W panel (2-3 seconds) Opener light will blink to confirm programming.
• 5
  Permanently mount the panel with provided hardware Use appropriate anchors for your wall type (drywall/concrete).
• 6
  Test the panel Press the button to open and close your garage door.

Need Help?

• 1
  Install 4 AA batteries in the smart panel Ensure correct polarity for optimal battery life.
• 2
  Mount the panel on your garage wall Choose a location within 40 feet of the opener with good signal.
• 3
  Press & release the yellow Learn button on opener Light comes on. You have 30 seconds.
• 4
  Press & hold the button on the L958W panel (2-3 seconds) LCD screen will show confirmation. Opener light blinks.
• 5
  Download the myQ app on your smartphone Connect your account and add the L958W panel for remote access.
• 6
  Test locally and via the myQ app Verify door opens/closes from both the panel and your phone.

  myQ provides real-time alerts and remote access

Need Help?

• 1
  Charge the VKP1-LM battery fully before first use Use the included USB charging cable. Allow 4-6 hours for full charge.
• 2
  Mount the video keypad on your garage wall Position at eye level (48-60 inches high) near your entry door.
• 3
  Press & release the yellow Learn button on opener Light comes on. You have 30 seconds.
• 4
  Press & hold the open/close button on the VKP1-LM (2-3 seconds) The video screen will show confirmation. Opener light blinks.
• 5
  Set up myQ connectivity for remote access Open the myQ app on your phone and add the video keypad.
• 6
  Test local and remote access Verify video feed, door control, and motion detection work properly.

  Built-in video allows you to see visitors before opening
• 7
  Configure motion alerts if desired Adjust sensitivity settings in the myQ app for optimal performance.

Need Help?

• 1
  Mount the camera in an optimal location Install near the ceiling pointed at your garage door for full visibility.
• 2
  Power the camera using the included power adapter Connect to an outlet with WiFi coverage. Let it boot up (1-2 minutes).
• 3
  Download the myQ app on your smartphone Create or sign in to your myQ account to begin setup.
• 4
  Add the camera to your myQ account Scan the QR code on the camera or enter the serial number in the app.
• 5
  Connect the camera to your home WiFi network Select your network from the app and enter your WiFi password.
• 6
  Link the camera to your garage door opener In the myQ app, select your opener and confirm the connection.
• 7
  Test remote access and door control Open the myQ app from another location and verify video/control works.

  You can now open/close your door and see live video from anywhere

Need Help?

Remote not working?

• Replace remote batteries with fresh ones
• Make sure you pressed Learn button within 30 seconds before pressing remote button
• Stand closer (within 20 feet) and try again
• Hold remote button for full 2-3 seconds continuously
• Try programming to a different button if available
• Clear all programming and start over (press Learn for 6+ seconds until light stops blinking)

Keypad not responding?

• Replace keypad batteries (check battery type: 4 AA or 2 AA depending on model)
• Move keypad closer to opener (should be within 40 feet)
• Make sure you pressed # button after typing PIN
• Double-check your PIN number (no leading zeros)
• Try a different PIN code to test functionality
• Clean keypad contacts if buttons are unresponsive

Safety sensors not detecting?

• Check that both sensors show steady red alignment lights
• Clean sensor lenses (use soft cloth—don’t scratch)
• Verify sensors face each other with clear line of sight
• Check all wire connections at both the sensor and opener
• Test with wire connections reversed (swap white/black at one end)
• Replace batteries in wireless sensor models

Opener Learn button light won’t come on?

• Check that garage door is fully closed
• Verify opener has power (check outlet/breaker/GFI reset)
• Press Learn button firmly for 1-2 seconds
• Try unplugging opener for 30 seconds, then plug back in
• If door moves when Learn button pressed, it’s a different type of opener—contact us
• If still no light, the opener may need professional service

Door reverses when it shouldn’t?

• Check that safety sensors are properly aligned
• Clean sensor lenses of dust and debris
• Verify nothing is blocking the door’s path
• Test door force settings (may need professional adjustment)
• Check for loose connections at the sensor terminals